Jump to content

Am I wrong?


Steven Hockstein

Recommended Posts

Mike, Thanks for the technical info. It is nice to know but I will never do this type of calculation as part of a home inspection. To me it is like calculating BTU requirements for a heating system and span ratings for floor joists as part of our home inspection. I specifically exclude technical analysis from a home inspection and offer more comprehensive analysis for an added cost.

The question is where is the line between what we do as a home inspection and technically analyzing the systems and structures in a home? I guess it is for each of us to decide where that line is for ourselves. We just need to be clear of what services we are providing for our clients and that we are meeting the standards or licensing requirements that govern our work.

When I noted that the electrical panel was overloaded I was referring to the fact that there was too much wiring stuffed into the panel box and what appeared to be an excessive amount of mini-breakers. Along with other electrical issues in the house, this triggered my concern about the quality of the electrical work. I punted to the electrician.

Link to comment
Share on other sites

Steve,

It arrived in my in-box. I'm just passing it on for folks to use it as they see fit. Me, I can't add a column of six single-digit numbers together five times in a row and get the right answer - I'm not kidding when I say I can't do second grade math - there's no way I'd attempt to do that calculating. I'd rather have my fingernails pulled out one by one verrrry slowwwwly.

Link to comment
Share on other sites

I plan to use Holt's load calc article as an attachment to reports that recommend such a calculation. My boilerplate will say 'ask an electrician to complete a load calculation on the house, or do it yourself if you're up to it'

Any copyright issues with that?

Marc

Link to comment
Share on other sites

Not to derail this thread, but what rule should be followed in this scenario?

150 amp panel 2 poles using this equation 150 Amp x 2 Poles = 300 / 10 = 30. There should only be 30 breakers.

The panel model number is rated for 40 breakers- qoc40uf.

Do you go off the equation or the manufacture label?

The panel listing is used, not an arbitrary formula that assumes a load of 10 amps per pole.

Link to comment
Share on other sites

First, look at the panel diagram. These often show the allowable number of tandem breakers, and where they are allowed. That does not work with CH, because they do not use a diagram. Next, look at the panel model number. Usually in the model number you will see the amperage (100, 200) the number of slots (30, 40) and the number of poles. As an example, 200C3040 would be a 200 amp panel with 30 slots and room for 40 poles (i.e. 10 tandem breakers). 100C20 would be a 100 amp panel with 20 slots and no tandems. 100C2024, you get the picture. This may not be 100% accurate, but it seems to be true most of the time.

As far as anything pre-2008 and probably most panels you will see after that time, if it is a 40 or 42 slot panel, my bet it that it is highly unlikely that tandems are allowed. If they are I suspect the panel should look unusually large to accommodate the extra wiring.

Link to comment
Share on other sites

Not to derail this thread, but what rule should be followed in this scenario?

150 amp panel 2 poles using this equation 150 Amp x 2 Poles = 300 / 10 = 30. There should only be 30 breakers.

The panel model number is rated for 40 breakers- qoc40uf.

Do you go off the equation or the manufacture label?

The panel listing is used, not an arbitrary formula that assumes a load of 10 amps per pole.

I agree that the panel listing is the simplest and surest method. The formula, however, is not arbitrary. It's part of the UL listing for CTL designated panelboards and it can be useful if the panel listing isn't visible or if it's been destroyed.

Link to comment
Share on other sites

For those who are interested in doing a load calc, you can follow the guidelines directly from the NEC, use the info from Mike Holt, use the very easy form in Code Check, or get the "Resi Electrical Load Calc Pro" app for your phone.

After doing them by hand for years, I really appreciate the app. It's fast, easy, and accurate.

Link to comment
Share on other sites

Not to derail this thread, but what rule should be followed in this scenario?

150 amp panel 2 poles using this equation 150 Amp x 2 Poles = 300 / 10 = 30. There should only be 30 breakers.

The panel model number is rated for 40 breakers- qoc40uf.

Do you go off the equation or the manufacture label?

The panel listing is used, not an arbitrary formula that assumes a load of 10 amps per pole.

I agree. The number of breakers, in the same way that the sum of the installed breakers, is a meaningless number.

Most panels I install now are 40/80 panels. What does this formula say about 80 poles??

Link to comment
Share on other sites

I am sure the panel is not listed for all the circuit breakers that are installed! 40 circuits (more than likely) with the main counted as 2. As far as the "no limit on number of breakers now," that is correct, "as long as the panel is Listed" for the number of breakers that are installed. That rule change does not affect existing panels!

I had not been counting the main. Should I be doing that?

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...